| Access Server: User's and Developer's Guide | ||
|---|---|---|
| <<< Previous | Next >>> | |
Submenu containing most important security settings, like passwords. |
Root password [buffy]
Default value for this option is "buffy". Password of "root" user, shown in encrypted form. To change the password, clear the field, enter a new password and click Save. Saving an empty field keeps the old password. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. |
Setup password [buffy]
Default value for this option is "buffy". Password of "root" user for WWW setup. To change the password, clear the field, enter a new password and click Save. Saving an empty field keeps the old password. |
iWRAP password [buffy]
Default value for this option is "buffy". The password required to be entered before any commands when communicating with iWRAP. To change the password, clear the field, enter a new password and click Save. Saving an empty field keeps the old password. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" to disable iWRAP password. |
Allow local clients without password [Yes]
Default value for this option is "Yes". If this setting is "Yes", iWRAP password is requested only from remote clients, not from local clients (127.0.0.1). |
Bluetooth PIN code []
Default value for this option is empty. This PIN code is used when establishing connections. Up to 16 characters can be used. If there is no default PIN code set, Access Server does not require a PIN code when establishing connections. However, if there is no default PIN code set, but the other device requests a PIN code, "1234" is replied. |
Root user password for FTP [buffy]
Default value for this option is "buffy". Password of the "root" user for FTP connections. |
Allow anonymous FTP login [Yes]
Default value for this option is "Yes". Whether "anonymous" FTP login is allowed or not. |
wpkgd autoinstall password []
Default value for this option is empty. This is optional password to authenticate wpk autoinstall packets (wpk packets sent to the autoinstall directory). The password is shown encrypted here, if set. To change the password, clear the field, enter a new password and click Save. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" do disable the password. The password must match the authentication parameter in the "wpkg.pif" file in the wpk packet. Otherwise the packet is not processed. Syntax in the "wpkg.pif" file: %wpkg-auth: auth |
wpkgd hotplug password []
Default value for this option is empty. This is optional password to authenticate wpk installation packets automatically run from USB memory dongles or Compact Flash memory cards. The password is shown encrypted here, if set. To change the password, clear the field, enter a new password and click Save. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" to disable the password. The password must match the authentication parameter in the "wpkg.pif" file in the wpk packet. Otherwise the packet is not processed. Syntax in the "wpkg.pif" file: %wpkg-auth: auth |
Submenu containing generic settings. |
Root password [buffy]
Default value for this option is "buffy". Password of "root" user, shown in encrypted form. To change the password, clear the field, enter a new password and click Save. Saving an empty field keeps the old password. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. |
Description of this unit [Access Server #1611280191]
Default value for this option is empty. The description helps to recognize this unit in BSM, finder or in your own applications. |
Use local syslog service [Yes]
Default value for this option is "Yes". This option determines whether syslog logs locally to /var/log/messages or not. Set this to No if you want to log to a remote syslog server. |
Size of syslog file [63]
Default value for this option is "63". Size of one syslog file. |
Number of rotated syslog files [3]
Default value for this option is "3". Number of rotated syslog files to keep. |
IP address of the remote syslog server [192.168.42.1]
Default value for this option is "192.168.42.1". The IP address of the device in the network to which syslog should log to. The remote device must be configured to accept syslogd connections from this Access Server. See the syslog documentation on the remote device for more information on how to configure that. |
Swap to NFS server [No]
Default value for this option is "No". Swap to NFS server. |
Hostname and directory for NFS swap [swap.localdomain:/var/swap]
Default value for this option is "swap.localdomain:/var/swap". Hostname and directory for NFS swap. |
NFS swap size in megabytes [64]
Default value for this option is "64". NFS swap size in megabytes. |
System clock tick [10000]
Default value for this option is "10000". Set the number of microseconds that should be added to the system time for each kernel tick interrupt (100Hz). Increasing val by 1 speeds up the system clock by about 100 ppm, or 8.64 sec/day. |
System clock frequency [0]
Default value for this option is "0". Set the system clock frequency offset. Frequency gives a much finer adjustment than the tick option. The value is scaled such that frequency 65536 speeds up the system clock by about 1 ppm, or 0.0864 sec/day. |
Set system clock [No]
Default value for this option is "No". Set system clock. |
Year [2007]
Default value for this option is "2007". Year. |
Month [7]
Default value for this option is "7". Month. |
Day of month [19]
Default value for this option is "19". Day of month. |
Hour [11]
Default value for this option is "11". Hour. |
Minute [17]
Default value for this option is "17". Minute. |
Second [16]
Default value for this option is "16". Second. |
Submenu containing network settings. |
Hostname of the unit [wrap]
Default value for this option is "wrap". The hostname of Access Server. Local applications will see this name. This name may be changed by dynamic network configuration. |
Domain of the unit [localdomain]
Default value for this option is "localdomain". The domain name of Access Server. Local applications will see this name. This name may be changed by dynamic network configuration. |
Enable Ethernet cable interface [Yes]
Default value for this option is "Yes". Set this option to Yes if you want to have the Ethernet cable interface enabled. If you don't use this interface, you may disable it to slightly increase security and system boot speed. |
Enable Wi-Fi interface [Yes]
Default value for this option is "Yes". Set this option to Yes if you want to have the Wi-Fi interface enabled (you can use the Wi-Fi interface with a supported Compact Flash Wi-Fi card or USB Wi-Fi dongle). If you don't use this interface, you may disable it to slightly increase security and system boot speed. |
Enable GPRS interface [No]
Default value for this option is "No". Set this option to Yes if you want to have the GPRS interface enabled. To use the interface, a supported Compact Flash GPRS card or a serial GPRS modem must be attached to Access Server. |
Time server (rdate) []
Default value for this option is empty. Hostname or IP address of the time server to be connected at system boot to retrieve correct time using the Time Protocol (RFC 868). NTP client is running by default, so rdate should not be needed at all. |
Update current time now (ntp) [/sbin/service ntpd sync]
Update current time now (ntp) from configured NTP servers. By default uses a random selection of 8 public stratum 2 servers. |
Zeroconf interface [nap]
Default value for this option is "nap". Defines the interface in which Zeroconf is running. Possible interface names are "nap", "gn" and "none". |
Default interface settings. By default, Ethernet and Bluetooth PAN-NAP interfaces are assigned to this interface. |
Use dynamic network configuration [Yes]
Default value for this option is "Yes". This option determines whether or not automatic configuration of the default network interface (nap) using DHCP should be attempted at boot. If set to no, you have to manually enter IP address and other network settings. |
IP address [192.168.42.3]
Default value for this option is "192.168.42.3". The IP address of Access Server. |
Subnet mask [255.255.255.0]
Default value for this option is "255.255.255.0". The network mask of Access Server. |
IP address of the default gateway [192.168.42.254]
Default value for this option is "192.168.42.254". The IP address of the default gateway in the LAN to which Access Server is connected. |
List of name server IPs [192.168.42.1 192.168.42.2]
Default value for this option is "192.168.42.1 192.168.42.2". The IP address(es) of the name servers, separated by space. |
Ethernet cable settings. |
Assign to default interface [Yes]
Default value for this option is "Yes". Assigns Ethernet (eth0) to default interface (nap) with settings specified in Default interface settings. Do NOT set this to No if you don't know what you are doing. There is a high risk that you end up with invalid network settings if you do so. If you need to set a static IP address to Access Server, do it in the Default interface settings. |
Use dynamic network configuration [Yes]
Default value for this option is "Yes". Use dynamic network configuration (DHCP) on Ethernet interface when it is not assigned to the default interface. |
IP address [192.168.43.3]
Default value for this option is "192.168.43.3". IP address of the Ethernet interface when it is not assigned to the default interface and dynamic network configuration is not in use. |
Subnet mask [255.255.255.0]
Default value for this option is "255.255.255.0". Network mask of the Ethernet interface when it is not assigned to the default interface and dynamic network configuration is not in use. |
Wi-Fi settings. |
Act as a Wi-Fi Access Point [No]
Default value for this option is "No". This option defines whether Access Server acts as a Wi-Fi Access Point when Wi-Fi is enabled. |
ESSID []
Default value for this option is empty. Access point network name (Service Set ID). |
Nickname []
Default value for this option is empty. The nickname, or station name. |
WEP encryption key []
Default value for this option is empty. WEP encryption key for Wi-Fi. Examples: 10 hex digits: "abcdef1234" 26 hex digits: "1234567890abcdef1234567890" or "1234-5678-90ab-cdef-1234-5678-90" 5 ASCII characters: "s:abcde" 13 ASCII characters: "s:abcdefghijklm" |
Extra commands for Access Point mode [/etc/sysconfig/ifup-wlan0]
Extra commands for Access Point mode. Use only if you know what you're doing. Here for example you can add allow/reject MAC addresses with "iwpriv" command. |
Assign to default interface [No]
Default value for this option is "No". Assigns Wi-Fi to default interface with settings specified in Default interface settings. |
Use dynamic network configuration [Yes]
Default value for this option is "Yes". Use dynamic network configuration (DHCP) for Wi-Fi interface. |
IP address [192.168.44.3]
Default value for this option is "192.168.44.3". IP address of Wi-Fi interface. |
Subnet mask [255.255.255.0]
Default value for this option is "255.255.255.0". Subnet mask of Wi-Fi interface. |
GPRS settings. |
Dial on demand [Yes]
Default value for this option is "Yes". If this option is set to Yes, the GPRS link is not opened at boot time but when there is data to be transferred. |
SIM card PIN code []
Default value for this option is empty. PIN code of the SIM card in the GPRS modem. |
Username [blue]
Default value for this option is "blue". Username for GPRS network. Contact your GSM operator for correct value. Some examples: Elisa/Finland: blue Sonera/Finland: blue Wataniya/Kuwait: blue Etisalat/UAE: Mnet See also: http://www.kh-gps.de/gprsset.htm |
Password [giga]
Default value for this option is "giga". Password for GPRS network. Contact your GSM operator for correct value. Some examples: Elisa/Finland: giga Sonera/Finland: giga Wataniya/Kuwait: giga Etisalat/UAE: Mnet See also: http://www.kh-gps.de/gprsset.htm |
Internet APN [internet]
Default value for this option is "internet". Internet APN for GPRS network. Contact your GSM operator for correct value. Some examples: Elisa/Finland: internet Sonera/Finland: internet Wataniya/Kuwait: action.wataniya.com Etisalat/UAE: mnet See also: http://www.kh-gps.de/gprsset.htm |
Extra parameters for pppd []
Default value for this option is empty. Optional extra parameters for pppd. Use only if you know what you are doing, for example if you want to debug ppp connections. |
Submenu containing settings of various applications. |
Default startup applications []
Change which applications are to be started at startup and which don't. |
Submenu containing settings for FTP server application. |
Root user password [buffy]
Default value for this option is "buffy". Password of the "root" user for FTP connections. |
Root user directory [/]
Default value for this option is "/". Root directory of the "root" user for FTP connections. |
Root user instances [5]
Default value for this option is "5". Maximum number of simultaneous logins of the "root" user for FTP connections. |
Allow anonymous login [Yes]
Default value for this option is "Yes". Whether "anonymous" FTP login is allowed or not. |
Anonymous user password [*]
Default value for this option is "*". Password of the "anonymous" user for FTP connections. Use "*" to allow everything (aka anonymous login). |
Anonymous user directory [/tmp/obex]
Default value for this option is "/tmp/obex". Root directory of the "anonymous" user for FTP connections. |
Anonymous user instances [5]
Default value for this option is "5". Maximum number of simultaneous logins of the "anonymous" user for FTP connections. |
Allow anonymous user to do everything [No]
Default value for this option is "No". Whether "anonymous" user is allowed to do everything (all below) or not. |
Allow anonymous user to download [Yes]
Default value for this option is "Yes". Whether "anonymous" user is allowed to download files or not. |
Allow anonymous user to upload [No]
Default value for this option is "No". Whether "anonymous" user is allowed to upload files and make directories or not. |
Allow anonymous user to overwrite [No]
Default value for this option is "No". Whether "anonymous" user is allowed to overwrite existing files or not. |
Allow anonymous user to multiple login [No]
Default value for this option is "No". Whether "anonymous" user is allowed to multiple logins or not. |
Allow anonymous user to erase [No]
Default value for this option is "No". Whether "anonymous" user is allowed to erase files and directories or not. |
Edit configuration file [/etc/ftpd.conf]
Edit the self documented configuration file of the FTP server. Here you can change more advanced settings. |
Submenu containing settings for ObexSender application. |
Bluetooth friendly name [W$S_$p]
Default value for this option is "W$S_$p". The name shown when this device is found when inquired about by other Bluetooth devices. Following meta tags are available: $S : Hardware serial number, all ten digits $s : Hardware serial number, last three digits $P : Server port $p : Server port, last digit $H : Fully Qualified Domain Name (FQDN) $h : hostname $$ : $ For example, "Server_$p" would set the Bluetooth friendly name as "Server_1" for first baseband, "Server_2" for second baseband and "Server_3" for third baseband. |
Minimum RSSI value before sending [-80]
Default value for this option is "-80". The working range of ObexSender can be configured or limited with this setting. When ObexSender searches for devices, the RSSI (Receiver Signal Strength Indicator) value is also measured. This value ranges from -128 to -1. 128 to -90 means the signal strength is very weak. A connection attempt would very likely fail. 80 to -65 means the signal strength is ok. Connection can be created. With Class 2 devices, like most mobile phones, this means the phone is 10-20 meters away. A Class 1 device can be even more than 100 meters away. Please note that -65 is recommended value for Access Server with serial number 0607239999 and smaller. 45 to -30 means the signal is very strong. The devices are most likely very close to each other (less than a meter away). For example testing purposes value -45 is ideal because you send only to devices very near to Access Server. With the serial numbers of 0607239999 and smaller, 35 or -40 can also be suitable. |
Whitelist RSSI limit [0]
Default value for this option is "0". Determines an RSSI limit that allows remote device to be removed from all block lists. This can be used in a way that you bring your device very close to Access Server and it will be able to receive content again, without waiting for OK- or FAIL-delays to pass. For example, you have received a file succesfully from ObexSender and you then have to wait for OK-delay to pass. You have configured whitelist RSSI limit to -45 (or -35 if serial number is less than 0607239999) and then you bring your device practically attached to Access Server. Now you have to wait for an inquiry to pass (blue led starts blinking and then stops). Then after a short while you should receive content again. |
Require pairing [No]
Default value for this option is "No". Use pairing to inform "I want to receive files". Enabling this means that user must first manually pair his or hers device with Access Server. |
Delete non-matching requests [Yes]
Default value for this option is "Yes". This setting applies if you're using REPLY-feature of ObexSender and you send a file to Access Server to receive specific content. Now, if the file you sent doesn't match to ObexSender configuration, the file is saved. Matching files are always deleted. Disable this if you have some other program doing ObjP/FTP. |
Register to watchdog daemon [Yes]
Default value for this option is "Yes". If this is enabled, ObexSender will reboot Access Server automatically if Bluetooth basebands have stopped responding. |
Upload a new file [/usr/local/obexsender/files]
This link allows you to upload files into the ObexSender file directory. |
List files [/usr/local/obexsender/files]
This link allows you to browse files on the ObexSender file system. |
Edit configuration file [/etc/obexsender.conf]
This link opens ObexSender configuration file (/etc/obexsender.conf) and allows you to edit it manually. It also allows you to change the settings that are not configurable with Setup application. |
Inquiry and calculate hash [/usr/sbin/obexsender-hash --download]
Inquiry and calculate hash. This feature allows you to expand the database of recognizable bluetooth devices. You can use this to calculate hash file from new device and send it to Bluegiga who will update and release new database. |
Restart ObexSender [/sbin/service obexsender restart]
Restart ObexSender. |
View log [-]
This link allows you to view ObexSender log file if it exists. By default a summary of the logged events is displayed. Detailed information is available by clicking the date links. |
Submenu containing ObexSender timeouts and delays. |
Delay between inquiries [10]
Default value for this option is "10". Delay between inquiries (Bluetooth device discoveries) in seconds. |
Delay between reply scans [10]
Default value for this option is "10". Determines how often (in seconds) obexserver's incoming directory is scanned for remote requests. A low value increases CPU usage. Basically this value affects on the delay that takes place when user sends file to Access Server to which ObexSender should reply with a certain file. |
If previous was ok, timeout before sending again [36000]
Default value for this option is "36000". If a file has been successfully sent to a device, this timeout (in seconds) defines when content can be sent again to the same device. |
If previous was fail, timeout before sending again [86400]
Default value for this option is "86400". If a file transmission to a device has failed or user has declined the file, this timeout (in seconds) defines when ObexSender can send content to the same device again. |
Delay between retrying call [120]
Default value for this option is "120". When user doesn't accept or reject the file, ObexSender will try to send the file again. This setting determines the timeout (in seconds) before resend occurs. If you wish to disable this feature you can use the same value as in OK-delay or FAIL-delay, i.e. the two previous settings. |
Delay after scanning [5]
Default value for this option is "5". When a remote request from user has been received, this setting determines how long (in seconds) ObexSender will wait until the response file is sent back to the user. Default value is 5 seconds, because some mobile phones are not able to receive files over Bluetooth until at least 5 seconds has passed from sending. |
Tester delay [60]
Default value for this option is "60". Determines how often content is pushed to a tester device. Tester device is a device that is always offered content, so it isn't blocked in any case. |
Pair expire timeout [0]
Default value for this option is "0". How long to keep the pairing. Zero means forever. |
Submenu containing ObexSender logging options. |
Logfile name [-]
Default value for this option is "-". Defines the path and name of the ObexSender log file (for example "/usr/local/obexsender/obexsender.log"). Log file contains information about successful and unsuccessful transmissions, timestamps and information about sent files. You can also use an IP address of a log server, which must be another Access Server running ObexSender. Type "-" to use syslog. |
Log prefix [-]
Default value for this option is "-". Prefix is put in front of every event in the log file. Type "-" for none. |
If sending was failure, log it too [Yes]
Default value for this option is "Yes". If this is enabled failed transmissions will be logged too. |
Verbosity level [0]
Default value for this option is "0". Determines the verbosity level of ObexSender logging. The value can be from 0 to 4. If this setting is set to "0", there will be minimal logging and with setting "4" there will be maximum amount of logging. WARNING! Full verbose logging (4) should be used only for debugging purposes, since it creates a lot of logs and the flash memory can be filled rather quickly. The only verbose level that should be used in production is 0 because other verbosity levels generate too much log and will eventually fill up Access Server. |
Block list save delay [0]
Default value for this option is "0". Determines how often (in seconds) a dump file is updated. Using dump file allows blocklist to be saved in case of power failure of Access Server. "0" disables this feature. We recommend to use a rather big value, for example 15min = 900s. WARNING: Using a small value here can physically burn the flash memory over time. |
Block list file name [/var/lib/obexsender/blocklist.dump]
Default value for this option is "/var/lib/obexsender/blocklist.dump". You can choose to save the information about already served devices, so you can form a so-called "block list". If this ignore list is saved in flash memory, it will be preserved even if Access Server is rebooted. This basically ensures that remote devices don't receive the same content even if Access Server is rebooted. |
This link will delete the current log file after confirmation. |
Connection forwarding enables you to configure Access Server to automatically open and maintain connections to specific Bluetooth devices. Connection forwarding also forwards the data from the Bluetooth connections to a defined application or IP address using a TCP socket. |
Delay between calls [20]
Default value for this option is "20". This is the delay between calls to Bluetooth devices. If the call fails this is the time Connector sleeps before trying to connect to that same or next device again. |
Logfile name [-]
Default value for this option is "-". Defines the path and name of the Connector log file (for example "/usr/local/connector/connector.log"). Type "-" to use syslog. |
Register to watchdog daemon [Yes]
Default value for this option is "Yes". If this is enabled, Connector will reboot Access Server automatically if Bluetooth basebands have stopped responding. |
Verbosity level [0]
Default value for this option is "0". Determines the verbosity level of Connector logging. The value can be from 0 to 4. If this setting is set to "0", there will be minimal logging and with setting "4" there will be maximum amount of logging. WARNING! Full verbose logging (4) should be used only for debugging purposes, since it creates a lot of logs and the flash memory can be filled rather quickly. |
Edit configuration file [/etc/connector.conf]
This link opens Connector configuration file (/etc/connector.conf) and allows you to edit it manually. It also allows you to change the settings that are not configurable with Setup application. |
#1 Bdaddr [-]
Default value for this option is "-". Bluetooth address of remote device, for example 00:07:80:80:bf:01. |
#1 Channel [-]
Default value for this option is "-". Bluetooth channel or UUID where to connect. |
#1 Command [-]
Default value for this option is "-". This is the application or TCP/IP address and port where the connection is forwarded. Example: 192.168.42.1:5001 /usr/local/bin/myapp |
Submenu containing settings for wpkgd application. |
wpkgd's autoinstall directory [@]
Default value for this option is "@". wpkgd will automatically check this directory for wpk files containing software update packets. Special meta, "@", means Obexserver's root directory. Use it if you want to allow updates via Bluetooth ObjP or FTP profiles. Use empty to disable autoinstall. |
Password for autoinstall packages []
Default value for this option is empty. This is optional password to authenticate wpk autoinstall packets (wpk packets sent to the autoinstall directory). The password is shown encrypted here, if set. To change the password, clear the field, enter a new password and click Save. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" do disable the password. The password must match the authentication parameter in the "wpkg.pif" file in the wpk packet. Otherwise the packet is not processed. Syntax in the "wpkg.pif" file: %wpkg-auth: auth |
Delete processed autoinstall packages [Yes]
Default value for this option is "Yes". If this option is set Yes, the wpk autoinstall packets are deleted after they have been processed. |
Process hotplug packages [Yes]
Default value for this option is "Yes". If this option is set to Yes, wpk packets are automatically processed from USB memory sticks or Compact Flash memory cards when they are plugged into Access Server. |
Password for hotplug packages []
Default value for this option is empty. This is optional password to authenticate wpk installation packets automatically run from USB memory dongles or Compact Flash memory cards. The password is shown encrypted here, if set. To change the password, clear the field, enter a new password and click Save. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" to disable the password. The password must match the authentication parameter in the "wpkg.pif" file in the wpk packet. Otherwise the packet is not processed. Syntax in the "wpkg.pif" file: %wpkg-auth: auth |
Delete processed hotplug packages [No]
Default value for this option is "No". If this option is set Yes, the wpk packets are deleted after they have been processed. |
Extra parameters for wpkgd []
Default value for this option is empty. Optional extra command line parameters for wpkgd. Please see wpkgd --help for detailed information on the options. |
Submenu containing settings for SMS gateway application. |
Modem device [/dev/ttyS0]
Default value for this option is "/dev/ttyS0". Modem device for SMS gateway. /dev/ttyAT1 for user uart /dev/ttyS0 for CF slot |
Log file name [-]
Default value for this option is "-". The file to which the SMS gateway (smsgw) logs all traffic. Use /dev/null for none, - for syslog, /var/log/smsgw.log if you want to save this information. Be careful not to fill the RAM file system (use a cron job to free disk space from time to time). |
SMSC number [+358405202000]
Default value for this option is "+358405202000". SMSC number. Contact your local GSM operator if you don't know the correct value. +358405202000 for Sonera/Finland +358508771010 for Elisa/Finland |
Edit configuration file [/etc/smsgw.conf]
Edit the self documented configuration file of the SMS gateway. |
Submenu containing all iWRAP related settings. |
iWRAP password [buffy]
Default value for this option is "buffy". The password required to be entered before any commands when communicating with iWRAP. To change the password, clear the field, enter a new password and click Save. Saving an empty field keeps the old password. Please note that the new password is shown in plain text only right after you have saved it. Later it is only shown encrypted, and there is no way to decrypt it. You must either remember it or change it again to something you do remember. Use "-" to disable iWRAP password. |
Allow local clients without password [Yes]
Default value for this option is "Yes". If this setting is "Yes", iWRAP password is requested only from remote clients, not from local clients (127.0.0.1). |
Friendly name [W$S_$p]
Default value for this option is "W$S_$p". The name shown when this device is found when inquired about by other Bluetooth devices. Following meta tags are available: $S : Hardware serial number, all ten digits $s : Hardware serial number, last three digits $P : Server port $p : Server port, last digit $H : Fully Qualified Domain Name (FQDN) $h : hostname $$ : $ For example, "Server_$p" would set the Bluetooth friendly name as "Server_1" for first baseband, "Server_2" for second baseband and "Server_3" for third baseband. |
Connectable and discoverable mode [3]
Default value for this option is "3". This setting specifies whether this device is connectable and/or discoverable by other Bluetooth devices. When a device is connectable, other Bluetooth devices can open a Bluetooth connection to it. Before opening a connection, the calling device must know the Bluetooth address of the device it is connecting to. The Bluetooth addresses can be found by making an inquiry. When a device is discoverable, it shows up in inquiries. Possible values for all combinations of these settings are: 0 : Not connectable, not discoverable 1 : Not connectable, discoverable 2 : Connectable, not discoverable 3 : Connectable and discoverable |
Master/slave role switch policy [1]
Default value for this option is "1". This setting specifies how local Bluetooth device should decide it's role. When a Bluetooth device connects another Bluetooth device, it is a master by default and the answering device is the slave. When the connection is being built, a role switch can be made. Normally, access point devices need to be the master, and therefore they require a master-slave switch when a new device is connecting. This is also how Access Server is configured by default. Otherwise Access server couldn't host the maximum number of slaves (7). Other possible combinations are: 0 : Allow switch when calling, don't request it when answering 1 : Allow switch when calling, request it when answering 2 : Don't allow switch when calling, request it when answering If you have problems connecting to Access Server, it might be because your client device does not support the master/slave switch. In this case you should change this setting to 0. |
Default PIN code []
Default value for this option is empty. This PIN code is used when establishing connections. Up to 16 characters can be used. If there is no default PIN code set, Access Server does not require a PIN code when establishing connections. However, if there is no default PIN code set, but the other device requests a PIN code, "1234" is replied. |
Power save mode and parameters [4]
Default value for this option is "4". The power save mode used by default for all connections. Possible settings are: 0 : Active 1 : Park: Round-robin 2 : Park: Idle 3 : Sniff: All 4 : Sniff: Idle "Active" means that no power saving is in use. "Sniff: All" means that the connections are kept in sniff mode always. "Sniff: Idle" means that a connection is switched to sniff mode after it has not transmitted data for some time (2 seconds by default). When data transmission resumes, switch to active mode is made. Park modes are generally not useful. See User's and Developer's Guide and Bluetooth specification for more information. |
Use literal replies in SDP [Yes]
Default value for this option is "Yes". If enabled, some SDP result codes will have literal values instead of numeric values. |
Optional command line parameters []
Default value for this option is empty. Optional extra command line startup parameters for the iWRAP servers. |
Edit startup script [/etc/bluetooth.conf]
Opens iWRAP configuration file (/etc/bluetooth.conf) for editing. You can add extra iWRAP commands to that file. iWRAP servers process the file each time they start. See the User's and Developer's Guide for iWRAP command reference. For example, an unique friendly name for each baseband can be added by using following lines: 10101 SET BLUETOOTH NAME Foobar 10102 SET BLUETOOTH NAME Barfoo 10103 SET BLUETOOTH NAME Buffy! |
Submenu for configuring the supported Bluetooth profiles. |
Enable Device ID profile [Yes]
Default value for this option is "Yes". Whether or not Device ID profile is enabled. |
Enable LAN access profile [No]
Default value for this option is "No". Whether or not the LAN Access Profile is enabled. |
Enable PAN user profile [No]
Default value for this option is "No". Whether or not the PAN User Profile is enabled. |
Enable PAN generic networking profile [No]
Default value for this option is "No". Whether or not the PAN Generic Networking Profile is enabled. |
Enable PAN network access point profile [No]
Default value for this option is "No". Whether or not the PAN Network Access Point Profile is enabled. |
Enable object push profile [Yes]
Default value for this option is "Yes". Whether or not the Object Push Profile is enabled. |
Enable file transfer profile [Yes]
Default value for this option is "Yes". Whether or not the File Transfer Profile is enabled. |
Submenu containing LAN Access Profile settings. |
Login name and password []
Default value for this option is empty. The login name and password required from LAN access clients. Must be entered as a single string, separated with a space. For example: guest buffy If empty, no login is required. |
Service channel [4]
Default value for this option is "4". Service channel for LAN access profile. |
Service name (shown in SDP) [LAN Access]
Default value for this option is "LAN Access". The name of the LAN Access Profile service shown in the Service Discovery. |
Defaultroute modification policy [0]
Default value for this option is "0". How the LAN Access Profile should modify the defaultroute in routing tables: 0: Do not alter defaultroute 1: When acting as a LAP client, set defaultroute according to the LAP server 2: When acting as a LAP server, set defaultroute according to the LAP client 3: Set defaultroute according to the LAP server/client connected |
First IP for LAP clients [192.168.160.0]
Default value for this option is "192.168.160.0". This defines the C-class of IP addresses to be used in point-to-point connections between Access Server and LAP clients. Full C-class is required: use "x.y.z.0". |
Submenu containing Personal Area Network User Profile settings. |
Service name (shown in SDP) [PAN User]
Default value for this option is "PAN User". The name of the PAN User Profile service shown in the Service Discovery. |
Enable zeroconf when calling [No]
Default value for this option is "No". Enable ZeroConf protocol for outgoing PANU connections. |
Enable zeroconf when answering [No]
Default value for this option is "No". Enable ZeroConf protocol for incoming PANU connections. |
Submenu containing Personal Area Network Generic Networking Profile settings. |
Service name (shown in SDP) [Generic Networking]
Default value for this option is "Generic Networking". The name of the PAN Generic Networking Profile service shown in the Service Discovery. |
Use dynamic network configuration for local IP address [No]
Default value for this option is "No". Whether or not DHCP is used for configuring local IP Address. Enable only if you are connecting this PAN-GN to another PAN-GN that will provide the IP configuration. |
Local GN interface IP address [192.168.161.1]
Default value for this option is "192.168.161.1". The IP address for the local GN interface. |
Local GN interface subnet mask [255.255.255.0]
Default value for this option is "255.255.255.0". The netmask for the local GN interface. |
Start DHCP server for remote users [Yes]
Default value for this option is "Yes". Whether or not this device should start DHCP for remote devices connecting to this PAN-GN. Disabled if "Use dynamic network configuration for local IP address" is used. |
First IP for lease block [192.168.161.2]
Default value for this option is "192.168.161.2". First IP address of the lease block. |
Last IP for lease block [192.168.161.254]
Default value for this option is "192.168.161.254". Last IP address of the lease block. |
Subnet of lease block [255.255.255.0]
Default value for this option is "255.255.255.0". Subnet mask of the lease block. |
Lease time [86400]
Default value for this option is "86400". Lease time in seconds. |
Submenu containing Personal Area Network Network Access Point Profile settings. |
Connection forwarding allows you to configure Access Server to automatically receive and forward Bluetooth connections to other applications or TCP socket. This submenu contains all the settigns related to connection forwarding capability. |
#1 Command [0.0.0.0:0]
Default value for this option is "0.0.0.0:0". This is the application or TCP/IP address and port where the connection is forwarded. For L2CAP connections, use the following format: "L2CAP:host:port". Example: 192.168.42.1:5001 /usr/local/bin/myapp |
#1 Service UUID [SERIALPORT]
Default value for this option is "SERIALPORT". This configures the Bluetooth profile that is used for connection forwarding. For L2CAP connections, use the following format: "L2CAP:UUID". See User's and Developers Guide for supported UUIDs. |
#1 Service channel [5]
Default value for this option is "5". RFCOMM channel or L2CAP psm for the Bluetooth profile configured in the "Service UUID" configuration. |
#1 Service name (shown in SDP) [Serial Port]
Default value for this option is "Serial Port". Name shown in Service Discovery. |
Submenu containing the Bluetooth Serial Port Profile settings. The profile itself is enabled and disabled by switching "serialport" application "on" or "off" from the menu: Setup -> Applications -> Default startup applications. |
Act as the calling device [No]
Default value for this option is "No". Whether this device should act as the calling device (DevA) or the answering device (DevB). |
BPS rate [115200]
Default value for this option is "115200". The bits-per-second rate of the connection. Possible values are: 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, and 460800. |
Data bits [8]
Default value for this option is "8". The number of data bits in the connection. Possible values are: 5, 6, 7, and 8. |
Parity [0]
Default value for this option is "0". The parity bit setting of the connection. Possible values are: 0: No Parity (default) 1: Odd Parity 2: Even Parity |
Stop bits [1]
Default value for this option is "1". The number of stop bits in the connection. Possible values are 1 and 2. |
Hardware flow control (RTS/CTS) [Yes]
Default value for this option is "Yes". Whether or not the hardware flow control is used. |
Software flow control (XON/XOFF) [No]
Default value for this option is "No". Whether or not the software flow control is used. |
Bluetooth address of the remote device [00:07:80:80:bf:01]
Default value for this option is "00:07:80:80:bf:01". The Bluetooth address of the device to be contacted. If the local device is configured as DevA, this is the DevB it tries to connect. |
Service channel [2]
Default value for this option is "2". In DevA (call) mode: The Bluetooth RFCOMM channel of the remote device. In DevB (answer) mode: The Bluetooth RFCOMM channel of the local device. |
Service name (shown in SDP) [Serial Port]
Default value for this option is "Serial Port". The name of the Bluetooth Serial Port Profile service shown in the Service Discovery. |
Optional command line parameters []
Default value for this option is empty. Optional extra parameters for the Access Server Serial Port profile application. Currently the supported parameters are: --device dev Device, if not the user port (/dev/ttyS0 for CF Card) --msc Enables transmitting of DCD/DSR Modem Status Control signals. --nobuffer Discard data if no Bluetooth connection, do not buffer it. |
This submenu contains Object Push Profile settings. |
Service channel [3]
Default value for this option is "3". Service channel for Object Push Profile. |
Service name (shown in SDP) [Object Push]
Default value for this option is "Object Push". The name of the Object Push Profile service shown in the Service Discovery. |
Root directory [/tmp/obex]
Default value for this option is "/tmp/obex". Root directory for obexserver application. The files received with Object Push Profile and File Transfer Profile are saved into this directory. Note: "/tmp/obex" is in RAM filesystem and will be erased during reboot. |
Optional parameters for server [--bdaddr $b --prefix $b-$P-]
Default value for this option is "--bdaddr $b --prefix $b-$P-". Optional parameters for obexserver application. See "obexserver --help" or User's and Developer's Guide for list of parameters. |
This submenu contains File Transfer Profile settings. |
Service channel [3]
Default value for this option is "3". Service channel for File Transfer Profile. |
Service name (shown in SDP) [File Transfer]
Default value for this option is "File Transfer". The name of the File Transfer Profile shown in the Service Discovery. |
Root directory [/tmp/obex]
Default value for this option is "/tmp/obex". Root directory for obexserver application. The files received with Object Push Profile and File Transfer Profile are saved into this directory. Note: "/tmp/obex" is in RAM filesystem and will be erased during reboot. |
Optional parameters for server [--bdaddr $b --prefix $b-$P-]
Default value for this option is "--bdaddr $b --prefix $b-$P-". Optional parameters for obexserver application. See "obexserver --help" or User's and Developer's Guide for list of parameters. |
Submenu containing advanced settings of Access Server. |
System startup script [/etc/rc.d/rc.local]
This is the last initialization script executed at system startup. By default, the script /etc/rc.d/rc.local just turns off all LEDs to indicate the startup has finished. If you want to initialize something automatically at every boot, or start up your own applications, you should add the required commands to this file. Remember to start your programs to the background. Example: /usr/local/bin/myapp & If you do not start the programs to the backgroud, you will not able to access the management console using a serial cable. |
Default user profile [/etc/profile]
Edit the file containing the default user profile settings. |
Setup access [/etc/setup.conf]
The "/etc/setup.conf" file can be used to give different access rights to different users of the WWW Setup. The file consist of lines in following format: example.tag +user1 +user2 -user3 -user4 This will allow (+) access to tag "example.tag" for "user1" and "user2" and denies (-) access from "user3" and "user4". You can find the tags from the output of Setup -> Advanced -> System Information -> Collect info for support request For example, the tag of this setting is advanced.setupconf. If you have created another user "guest" in /etc/httpd.conf that can access "/setup", you can deny that user from changing the Setup access settings with following line in this file: advanced.setupconf -guest |
Edit other configuration files []
From this menu you can edit any files located in Access Server file system. You can for example create "/var/spool/cron/crontabs/root" file for configuring the cron daemon. |
Browse /tmp/obex files [/tmp/obex]
Browse files stored in /tmp/obex directory. |
Browse all files []
Browse all files stored in Access Server. |
Find other Access Servers [/usr/sbin/finder]
Find other Access Servers in the network. |
Upload a software update [/tmp/obex]
Upload a software update file (*.wpk). Access Server supports a special management packet format (wpk), which can be used to update Access Server software components or to install custom software and configuration files. Please consult User's and Developer's Guide for more information. |
This submenu contains advanced Bluetooth commands. |
Inquiry for Bluetooth devices [/usr/bin/btcli inquiry]
This command runs a standard inquiry command and lists found devices. See User's and Developer's Guide for more information about inquiry. |
Set Bluetooth radios to class 1 [/usr/sbin/btclass 1]
This commands sets Bluetooth radios to class 1 power levels, max. +20dBm. |
Set Bluetooth radios to class 2 [/usr/sbin/btclass 2]
This commands sets Bluetooth radios to class 2 power levels, max. +4dBm. |
Set Bluetooth radios to class 3 [/usr/sbin/btclass 3]
This commands sets Bluetooth radios to class 3 power levels, max. 0dBm. |
This submenu contains tools to retrieve system status information. |
Hardware information
Displays hardware and software identification information (output of command "wrapid"). |
List installed software components [/usr/bin/dpkg -l]
Lists currenty installed software components and their version numbers. |
List running processes [/bin/ps ww]
Lists running processes (output of command "ps"). |
List memory status [/usr/bin/free]
Lists memory status (output of command "free"). |
List free disk space [/bin/df -h]
Lists free disk space (output of command "df -h"). |
Show syslog file [/var/log/messages]
Shows syslog file. |
Show boot log file [/var/log/dmesg]
Shows boot log. |
Collect info for support request [/usr/sbin/supportinfo]
This page contains collectively all the system status and configuration information. Include this information when sending a support request to support@bluegiga.com WARNING: All classified information, like passwords, should be automatically excluded. It is still recommended to manually check that all such information is really removed. |
Reboot Access Server. Confirmation will be asked. |
Security settings
Root password [buffy]
Setup password [buffy]
iWRAP password [buffy]
Allow local clients without password [Yes]
Bluetooth PIN code []
Root user password for FTP [buffy]
Allow anonymous FTP login [Yes]
wpkgd autoinstall password []
wpkgd hotplug password []
Generic settings
Root password [buffy]
Description of this unit [Access Server #1611280191]
Use local syslog service [Yes]
Size of syslog file [63]
Number of rotated syslog files [3]
IP address of the remote syslog server [192.168.42.1]
Swap to NFS server [No]
Hostname and directory for NFS swap [swap.localdomain:/var/swap]
NFS swap size in megabytes [64]
System clock tick [10000]
System clock frequency [0]
Set system clock [No]
Year [2007]
Month [7]
Day of month [19]
Hour [11]
Minute [17]
Second [16]
Network settings
Hostname of the unit [wrap]
Domain of the unit [localdomain]
Default interface settings
Use dynamic network configuration [Yes]
IP address [192.168.42.3]
Subnet mask [255.255.255.0]
IP address of the default gateway [192.168.42.254]
List of name server IPs [192.168.42.1 192.168.42.2]
Enable Ethernet cable interface [Yes]
Ethernet cable settings
Assign to default interface [Yes]
Use dynamic network configuration [Yes]
IP address [192.168.43.3]
Subnet mask [255.255.255.0]
Enable Wi-Fi interface [Yes]
Wi-Fi settings
Act as a Wi-Fi Access Point [No]
ESSID []
Nickname []
WEP encryption key []
Extra commands for Access Point mode [/etc/sysconfig/ifup-wlan0]
Assign to default interface [No]
Use dynamic network configuration [Yes]
IP address [192.168.44.3]
Subnet mask [255.255.255.0]
Enable GPRS interface [No]
GPRS settings
Dial on demand [Yes]
SIM card PIN code []
Username [blue]
Password [giga]
Internet APN [internet]
Extra parameters for pppd []
Time server (rdate) []
Update current time now (ntp) [/sbin/service ntpd sync]
Zeroconf interface [nap]
Applications
Default startup applications []
FTP server settings
Root user password [buffy]
Root user directory [/]
Root user instances [5]
Allow anonymous login [Yes]
Anonymous user password [*]
Anonymous user directory [/tmp/obex]
Anonymous user instances [5]
Allow anonymous user to do everything [No]
Allow anonymous user to download [Yes]
Allow anonymous user to upload [No]
Allow anonymous user to overwrite [No]
Allow anonymous user to multiple login [No]
Allow anonymous user to erase [No]
Edit configuration file [/etc/ftpd.conf]
ObexSender settings
Bluetooth friendly name [W$S_$p]
Minimum RSSI value before sending [-80]
Whitelist RSSI limit [0]
Require pairing [No]
Timeouts and delays
Delay between inquiries [10]
Delay between reply scans [10]
If previous was ok, timeout before sending again [36000]
If previous was fail, timeout before sending again [86400]
Delay between retrying call [120]
Delay after scanning [5]
Tester delay [60]
Pair expire timeout [0]
Logging
Logfile name [-]
Log prefix [-]
If sending was failure, log it too [Yes]
Verbosity level [0]
Block list save delay [0]
Block list file name [/var/lib/obexsender/blocklist.dump]
Delete non-matching requests [Yes]
Register to watchdog daemon [Yes]
Upload a new file [/usr/local/obexsender/files]
List files [/usr/local/obexsender/files]
Edit configuration file [/etc/obexsender.conf]
Inquiry and calculate hash [/usr/sbin/obexsender-hash --download]
Restart ObexSender [/sbin/service obexsender restart]
View log [-]
Delete log (confirm)
Delete log now! [/bin/false]
Connector settings
Delay between calls [20]
Logfile name [-]
Register to watchdog daemon [Yes]
Verbosity level [0]
Edit configuration file [/etc/connector.conf]
#1 Bdaddr [-]
#1 Channel [-]
#1 Command [-]
wpkgd settings
wpkgd's autoinstall directory [@]
Password for autoinstall packages []
Delete processed autoinstall packages [Yes]
Process hotplug packages [Yes]
Password for hotplug packages []
Delete processed hotplug packages [No]
Extra parameters for wpkgd []
SMS gateway settings
Modem device [/dev/ttyS0]
Log file name [-]
SMSC number [+358405202000]
Edit configuration file [/etc/smsgw.conf]
iWRAP settings
iWRAP password [buffy]
Allow local clients without password [Yes]
Friendly name [W$S_$p]
Connectable and discoverable mode [3]
Master/slave role switch policy [1]
Default PIN code []
Power save mode and parameters [4]
Use literal replies in SDP [Yes]
Optional command line parameters []
Edit startup script [/etc/bluetooth.conf]
Bluetooth profiles
Enable Device ID profile [Yes]
Enable LAN access profile [No]
LAN access profile settings
Login name and password []
Service channel [4]
Service name (shown in SDP) [LAN Access]
Defaultroute modification policy [0]
First IP for LAP clients [192.168.160.0]
Enable PAN user profile [No]
PAN user profile settings
Service name (shown in SDP) [PAN User]
Enable zeroconf when calling [No]
Enable zeroconf when answering [No]
Enable PAN generic networking profile [No]
PAN generic networking profile settings
Service name (shown in SDP) [Generic Networking]
Use dynamic network configuration for local IP address [No]
Local GN interface IP address [192.168.161.1]
Local GN interface subnet mask [255.255.255.0]
Start DHCP server for remote users [Yes]
First IP for lease block [192.168.161.2]
Last IP for lease block [192.168.161.254]
Subnet of lease block [255.255.255.0]
Lease time [86400]
Enable PAN network access point profile [No]
PAN network access point profile settings
Service name (shown in SDP) [Network Access]
Connection forwarding
#1 Command [0.0.0.0:0]
#1 Service UUID [SERIALPORT]
#1 Service channel [5]
#1 Service name (shown in SDP) [Serial Port]
Serial port profile settings
Act as the calling device [No]
BPS rate [115200]
Data bits [8]
Parity [0]
Stop bits [1]
Hardware flow control (RTS/CTS) [Yes]
Software flow control (XON/XOFF) [No]
Bluetooth address of the remote device [00:07:80:80:bf:01]
Service channel [2]
Service name (shown in SDP) [Serial Port]
Optional command line parameters []
Enable object push profile [Yes]
Object push profile settings
Service channel [3]
Service name (shown in SDP) [Object Push]
Root directory [/tmp/obex]
Optional parameters for server [--bdaddr $b --prefix $b-$P-]
Enable file transfer profile [Yes]
File transfer profile settings
Service channel [3]
Service name (shown in SDP) [File Transfer]
Root directory [/tmp/obex]
Optional parameters for server [--bdaddr $b --prefix $b-$P-]
Advanced settings
System startup script [/etc/rc.d/rc.local]
Default user profile [/etc/profile]
Setup access [/etc/setup.conf]
Edit other configuration files []
Browse /tmp/obex files [/tmp/obex]
Browse all files []
Find other Access Servers [/usr/sbin/finder]
Upload a software update [/tmp/obex]
Bluetooth commands
Inquiry for Bluetooth devices [/usr/bin/btcli inquiry]
Set Bluetooth radios to class 1 [/usr/sbin/btclass 1]
Set Bluetooth radios to class 2 [/usr/sbin/btclass 2]
Set Bluetooth radios to class 3 [/usr/sbin/btclass 3]
System information
Hardware information
List installed software components [/usr/bin/dpkg -l]
List running processes [/bin/ps ww]
List memory status [/usr/bin/free]
List free disk space [/bin/df -h]
Show syslog file [/var/log/messages]
Show boot log file [/var/log/dmesg]
Collect info for support request [/usr/sbin/supportinfo]
Reboot system (confirm)
Reboot now! [/sbin/reboot]
|
| <<< Previous | Home | Next >>> |
| Directory Structure | Open Source Software Licenses |